Welcome to the website of Dongguan Tuowa Machinery Manufacturing Co., Ltd!
丨 Sitemap
丨 Product
丨 contact us
丨 CN
-
Focus on the production of tool grinders and multi-functional tool grinders
- Service hotline：
- 138-2575-1784
News
1. Firstly, confirm the material of the drill bit, select the appropriate grinding wheel according to the material of the drill bit, and install it on..
View More
After the power is turned on, turn on the power controller, set the tapping speed, press and hold the forward rotation, the servo motor converts the voltage signal into torque and speed output for tapping, and press and hold the reverse button when tapping to the bottom to withdraw. The work wire ha..
View More
1. The operator can only operate after passing the examination and obtaining the operation certificate. The operator should be familiar with the performance and structure of the machine, 2. Before work, check according to the requirements of the equipment spot check card, and inject oil according to..
View More
请使用者使用钻头研磨机前后以空压枪，清洁所有机台灰层铁屑，尤其是研磨接触孔之清洁，以确保机台使用寿命。更换砂轮正确方法，松开固定螺丝，打开砂轮保护盖，取下砂轮固定螺丝及扇叶片，取出砂轮，将砂轮及轴心接触面擦拭干净，砂轮新品装入轴心，扇叶片及固定螺丝装回，再将固定螺丝锁紧，盖回砂轮保护盖，锁上外壳固定..
View More
电动攻丝机是一种可对各种小型及大型钢件的粗牙、细牙、非标牙距的正转及反转紧固连接螺纹、传动连接螺纹及管螺纹进行内螺纹攻丝机床，该类机床属柔性攻丝范畴，显著特点是可折臂操作，适应M42以下螺纹攻丝要求。制动方式齿轮车身重量50kg目录1简介2特点3技术参数4操作方法5组成结构简介编辑electrict..
View More
1.开机前检查电机的电压和频率是否和电源一致。2.机床电源插头、插座上的各触角应紧固可靠，无松动或接触不良现象。3.当发生故障或有不正常声音应立即拔掉插头，然后进行检查修理。4.不要让机床在无人情况下运转，一定要在开机后，停止运转才能离开。外界切断电源，应按红色钮，否则机床会无人情况下来运转。5.不..
View More
夹头组之组装夹具组装步骤1.先确定钻头材质，并选用合适之砂轮使用。※CBN砂轮适用HSS(高速钢)材质、SD砂轮适用钨钢材质。2.将左侧调整台调整刻度归零：顺时针旋转到底,逆时针调到“0”的位置。A.选择适用筒夹放入夹头座。(以45°将筒夹嵌入夹头座)B.放入顺序：筒夹及夹头座与固定夹头螺帽链接，再..
View More
1.1 The machine has passed the qualification inspection and strict packaging treatment before delivery, but in consideration of the transportation process and other factors, special attention should be paid before installation. If there is any abnormality, please inform the product dealer or the rel..
View More
scan
开云(中国)
138-2575-1784
